返回
【17】Drilling Formula
- 1、 Pressure loss in annulus
- 2、 Pressure loss in annulus with corrected coefficient
- 3、 Pressure loss through the drill string with tool joint coefficient
- 4、 Total Flow Area Table
- 5、 Pressure loss through surface equipment
- 6、 Pressure loss through the drill string
- 7、 Impact Force of Jet Nozzles on Bottom Hole
- 8、 Cutting Slip Velocity Method#2
- 9、 Cutting Slip Velocity Method#1
- 10、 Power Law Constant
- 11、 Minimum Flow Rate for PDC bit
- 12、 Reynold Number
- 13、 Hydraulic Horse Power (HPP)
- 14、 Effective Viscosity
- 15、 Cutting Carrying Index
- 16、 Cross Flow Velocity Under a Drilling Bit
- 17、 Critical Flow Rate
- 18、 Bit Hydraulic Horsepower Per Area of Dril Bit (HSI)
- 19、 Bit Hydraulic Horsepowe (hp)
- 20、 Bit Aggressiveness (Coefficient of Friction)
- 21、 Bit Nozzle Velocity
- 22、 Stuck Pipe Calculation
- 23、 Pump Pressure and Pump Stroke Relationship
- 24、 Balance Cement Plug Above Retainer
- 25、 Squeeze Below Retainer and Balance Cement Plug Above Retainer
- 26、 Increase in casing pressure due to kick penetration Assumption - vertical well
- 27、 Tensile Capacity of Drillpipe
- 28、 Bottle Capacity Required in Accumulator
- 29、 Trip margin calculation
- 30、 Time to petentrate the kick
- 31、 Riser Margin
- 32、 New Pump Pressure With New Strokes (psi)
- 33、 New Pressure Loss With New Mud (psi)
- 34、 Mud Increment (MI)
- 35、 Maximum surface pressure from kick tolerance information
- 36、 Maximum Surface Pressure from Gas Influx in Water Based Mud
- 37、 Maximum pit gain from gas kick in water based mud
- 38、 Maximum Allowable Shut-In Casing Pressure (MASICP)
- 39、 Maximum influx height
- 40、 Maximum formation pressure (FP)
- 41、 Lube Increment (MI)
- 42、 Kill Mud Weight
- 43、 Kick tolerance factor (KTF)
- 44、 Initial Circulating Pressure (psi)
- 45、 Hydrostatic Pressure Loss Due to Gas Cut
- 46、 Initial Circulating Pressure (psi)
- 47、 Formation Pressure from Kick Analysis
- 48、 Estimate Type of Influx (kick)
- 49、 Estimate gas migration rate with an empirical equation.
- 50、 Calculate Influx Height
- 51、 Adjusted maximum allowable shut-in casing pressure for new mud weight
- 52、 Acutal gas migration rate
- 53、 Pump out
- 54、 Pressure required to break circulation
- 55、 Pipe Elongation Due to Temperature
- 56、 Equivalent Circulating Density (ECD) Using Yield Point for MW more than 13 ppg
- 57、 Maximum ROP Before Fracturing Formation
- 58、 Volume of Cutting Generated While Drilling
- 59、 Equivalent Circulating Density (ECD) Using Yield Point for MW less than 13 ppg
- 60、 Margin of Over Pull
- 61、 Loss of hydrostatic pressure due to filling water into annulus in case of lost return
- 62、 Light weight spot fill to balance formation pressure
- 63、 Lag Time Calculation
- 64、 Effective Mud Density
- 65、 Drill Collar Weight Calculation To Prevent Drill Pipe Buckling
